Anodizing System 5 gal (LCD Anodizing Kit) LQ#45

SKU: ANOD

$817.03$1,452.21

In Stock
SKU: ANOD Category:

Please download and read the instructions before purchasing Download here

Provides a durable anodized surface – which can easily be dyed.

Simple to operate – Predictable consistent results

Low Current Density means – Inexpensive power source

Low Current Density means – No heat buildup in the tank

VERY dilute chemical requirement – Environmentally friendly

No fumes – SAFER in confined areas

Fully Expandable – Kits can be made bigger by obtaining larger plastic containers

Conforms to Mil Spec A 8625 F

Kit does not contain immersion heaters.  If you require heaters, please visit www.industrialelectricheating.com, Kit also Requires Battery Acid that is not supplied but can be purchased at your local NAPA

 

THE STANDARD KIT DOES NOT INCLUDE A POWER SUPPLY

 

 

At this stage of the process the film has microscopic pores (see picture) which have to be sealed (or ‘fixed’) by dipping the part into sealer for 15 minutes. The part may be colored prior to boiling by simply soaking in our range of professional anodizing dyes. An almost infinite range of colors can be produced by mixing the dyes together.

 

The most exciting part of aluminum anodizing, is without doubt, experimenting with the amazing array of colors and effects one can produce, with a little practice and skill. The metal can be pretreated in a variety of ways, polished, scratch brushed etc., the anodize film grown, and then the colors applied prior to sealing the anodize surface, permanently locking the colors into the metal. The system is ideal for paint ball guns, model aircraft parts, and prototype work. The manual and DVD discuss the numerous techniques for dyeing, including multicolor, ‘splash’ dyeing, silk screen printing, air brush spraying etc. Anodizing Colors

Anodized aluminum has a very durable surface that is unaffected by weather and many chemicals. The surface will resist high temperatures, even a blowtorch, for short periods.

The issue of safety whilst anodizing is addressed by the use of plastic fume balls and a chemical mist suppressant, both of which float on the surface of the anodizing tank. During operation, no dangerous fumes are evident. Anodize Fume Suppressant may also be used on any sulfuric acid electro-stripping or etching tanks.

Don’t rely on mist suppressants entirely, they ALL break down eventually. Fume balls are permanent and they help control heat loss & evaporation, maintaining a more even tank temperature. Don’t settle for kits that don’t come with fume balls.

Anodizing Sealant. This is the product the commercial anodizers use. Add only 1 oz per gal of distilled water, and heat to boil for 15-20 mins. 1lb pack makes 16 gals solution.

Aluminum De-Oxidizer & De-Smut. This is the product the commercial anodizers use, a liquid concentrate, added to distilled water, to make a pre-anodize dip which de-smuts, removes unwanted materials such as copper, silicone & magnesium and prepares the metal for immediate anodizing. This is useful on alloys prone to smutting when placed into the anodizing tank. (Usually found on many Japanese motorcycle parts.) Aluminum De-Oxidizer & De-Smut is a chrome-free liquid de-oxidizer for a wide range of alloys. It operates at room temperature and is also an excellent de-oxidizer for aluminum alloys prior to chromating.

Anodize & Chrome Stripper is a super fast commercial grade stripper. It outperforms all others in speed and quality. Does not attack the aluminum. 1 lb makes 3 gallons.

Battery acid makes up ALL types of anodizing baths (just add distilled water). No need to carry different solutions for different anodizing tasks.

Buying quality battery acid locally saves shipping hazardous materials and HAZMAT charges. It costs next to nothing, so much larger setups can be produced at minimum cost, and if you contaminate the tank, it is inexpensive to replace, unlike pre-made solutions.

Additional tanks will be required if you want to dye with more than one color. Some smaller plastic tanks for rinsing will also be required. An acid resistant circulation system, or clean air agitation system will be required in the anodizing tank. Installing some small diameter PVC pipe on the bottom of the anodizing tank, with small holes drilled in the top, and then blowing filtered compressed air through the piping works well.

Contains Hazardous Goods. Shipping restrictions apply.

* – Larger rectifier may be required depending on immersed part surface area. Requirements are 4.5 amps per square foot for 90 min anodizing time.

Let us know if you already have the Caswell Plating Manual, and we will deduct $25 from cost of kit.

Standard Kit Contains:

  • 4 x 6 gal tanks with lids (12″ diam x 14″ deep)
  • 2 x 8.5 gal. enamel tank with lid for dying and sealing–place on hot plate to heat
  • 1 x Glass Thermometer
  • 1 x Rinsing Sprayer
  • 1 pack Mist Balls
  • 1 x 4oz Anodize Fume Suppressant – treats 48 gals of Anodizing Solution
  • 1 x 1lb Anodizing Sealant – makes 8 gallons
  • 1 x 2lb Aluminum Degreaser – makes 3 gallons
  • 2 x 1 qt De-oxidizer – makes 4.5 gallons
  • 2 x 8″ x 8″ GP Plates
  • 1 x Agitator Pump
  • 2 x Titanium Wires
  • 6 x Aluminum Strips (1 for tank bar, 5 for testing)
  • 2 x 1lb Anodize & Chrome Stripper – Makes 6 Gal
  • 1 x Color Wheel
  • The Caswell Plating Manual
  • Requires 1 gallon Battery Acid – not supplied

THE STANDARD KIT DOES NOT INCLUDE A POWER SUPPLY

Deluxe Kit (1) Contains:

  • 4 x 6 gal tanks with lids (12″ diam x 14″ deep)
  • 2 x 8.5 gal. enamel tank with lid for dying and sealing–place on hot plate to heat
  • 1 x Glass Thermometer
  • 1 x Rinsing Sprayer
  • 1 pack Mist Balls
  • 1 x 4oz Anodize Fume Suppressant – treats 48 gals of Anodizing Solution
  • 1 x 1lb Anodizing Sealant – makes 8 gallons
  • 1 x 2lb Aluminum Degreaser – makes 3 gallons
  • 2 x 1 qt De-oxidizer – makes 4.5 gallons
  • 2 x 8″ x 8″ GP Plates
  • 1 x Agitator Pump
  • 2 x Titanium Wires
  • 6 x Aluminum Strips (1 for tank bar, 5 for testing)
  • 2 x 1lb Anodize & Chrome Stripper – Makes 6 Gal
  • 1 x Color Wheel
  • The Caswell Plating Manual
  • 30 amp Constant Current Power Supply (for parts up to 6 sq ft)
  • Requires 1 gallon Battery Acid – not supplied

 

CHOOSE FROM ANODIZING DYES:

Note: All dyes are suitable for high temp and low temp sealants, except Grey BL and Yellow 4A, which should not be sealed using LT Sealer.

Please download and read the instructions before purchasing Download here

Weight 42 lbs
Dimensions N/A
Size

,